YSHIELD® Magnetic field shielding film MCL61 | MF | Width 61 cm | 1 meter
Novel film to shield LF magnetic fields with 30 dB attenuation = 97 %.
Screening attenuation: The indicated dB-values apply to 1 GHz. Measurement from 40/600 MHz to 40 GHz according to standards ASTM D4935-10 or IEEE Std 299-2006, view report below.
Order quantity: From 1 running meter in steps of 0.1 running meters. Will be cut off according to customer’s requirements, no right of withdrawal. Request a free sample before ordering.
PDF: Report screening attenuation
Content: 0.61 square meter
Weight: 162 g
Article number: MCL61
Packaging: 620x50x50 mm
MCL61 is our novel magnetic shielding film made from an amorphous cobalt alloy for shielding of low-frequency alternating magnetic fields. Also shields low-frequency electric alternating fields (LF) and high-frequency fields (HF).
Statical magnetic fields: Other than stated in the headline, this product is not MUMETALL®. We are utilizing a newer alloy which provides a better shielding. MUMETALL® is promoted to shield statical magnetic fields, refered to the usually used foils (material thickness 0.1 mm) the effect of the shielding is quite low indeed. We are using cobalt based alloy which attenuation is increasing from strength to strength of the velocity of the magnetic fields. There are no velocities by statical magnetic fields or by permanent magnets, that is why this product won´t shield those.
In comparison with MUMETALL® our new MCL61 has many advantages: MUMETALL® is soft and sensitive, on bending, to shocks and on processing it looses the attenuation very fast. The cobalt strips in our MCL61 are flexible but hard even at small bending radii. The attenuation remains constant even at high mechanical stress. Because the cobalt strips are only 20 µm thin, 50 mm width and sharp like a knife, we laminate it for protection. Due to the lamination MCL61 is corrosion-resistant even in humid environments. With a width of 61 cm big areas are shielded faster compared to 15 cm width MUMETALL®-strips. MCL61 can easily be cut with scissors.
- Width: 61 cm
- Length: By the meter / 20 m roll / 290 m roll; Because of the high production costs, we allow to divide up the ordered quantity!
- Attenuation LF magnetic field: 30 dB (97 %); The attenuation depends on the number of phases, cable twisting, the size of the area, etc.; Work in large areas: Shield cables with 1-2 sheets, fuse-boxes with 2-4 sheets;
- Attenuation HF: 75 dB
- Weight: 265 g/m²; Material thickness: 0.1 mm; Color: Silver
- Permeability: µ 2 = 10,000; µ 4 = 25,000; µ max. = 100,000;
- Saturation polarization Bs: 0.55 T
- Coercive field strength Hc: 0.5 A/m
- Remanence Br/Bs: 0.7
- Curie temperature Tc: 225 °C
- Materials: Polyester, Co69, Fe4, Mo4, Nb1, Si16, B7
Warning: The cutting edges are sharp like a knife! Important: Its difficult to glue the film free of creases, best cover the area with solid wall coverings. Wall, ceiling, floor: Best use a high-viscous assembly adhesive, that adheres to non-absorbent substrates. Smooth the glue, lay up the film, smooth with a pressure roller or squeegee. The sheets of MCL61 should be overlapped, level out the overlappings, paint it over with any commercial synthetic dispersion paint. Please pay attention that the film is a water vapour barrier on wall areas!
MCL61 is electrically isolated. To ground it, every strip has to be screwed with a chopper disk, that penetrates the polyester film. The grounding set MCL contains all for 10-20 strips.
The shielding attenuations are regularly tested in our own laboratory, HF due to ASTM D4935-10, the LF magnetic field due to ASTM A698/A698M-07. You find the test report above.