Electrical products | Cables | (N)YM(St)-J

Close filters
 
  •  
from to
  •  
  •  
No results were found for the filter!
 Shielded cable (N)YM(St)-J | 3 x 1.5 mm² | 1 meter Shielded cable (N)YM(St)-J | 3 x 1.5 mm² | 1 meter
Low priced shielded installation cables for the protection against low-frequency electric fields (LF). For installations over, up, in and under finery, in dry, moistens and wet areas, as well as in the brick-work and concrete. Also suitable for use outside, if protected against sun exposure. Excluded for direct imbedding in vibration, shaking and ramming concrete. Technical data Shielded PVC-sheathed cable (adapted to DIN VDE 0250 part 204/209) PVC self-extinguishing and flame retardant according to VDE 0482-332-1-2, DIN EN 60332-1-2 / IEC 60332-1 (equivalent DIN VDE 0472 part 804 test method B) CE = This product is conform with the EC Low-Voltage Directive 2006/95/EG Direct current resistance to DIN VDE 0295 Operating temperature -40°C to +70°C, cabling temperature -5°C to +70°C Nominal voltage U0/U: 300/500 V, current load according to VDE 0100 Test procedures according to DIN VDE 0472, test ac voltage 50 Hz, 2000 V Bending radius accoording to DIN VDE 0298: 4 x D Radiation resistance: Up to 80x106 cJ/kg (up to 80 Mrad) Variants Wire count / cross section Outer diameter Weight 3 x 1.5 mm² 10.5 mm 154 g/m 3 x 2.5 mm² 12.0 mm 217 g/m 5 x 1.5 mm² 12.0 mm 208 g/m 5 x 2.5 mm² 13.5 mm 208 g/m Construction 1) Solid copper conductor; 2) Insulation: cross linked polyethylene; 3) Common PVC core covering; 4) (St)-Screen: Coated aluminium foil with 1.5 mm wire; 5) PVC outer sheath; Information on installing Connect the ground wiring of the junction box with the ground wiring of the cable during installation! Always connect green-yellow with green-yellow , in no case connect it with the continuity wire! Protect the bare continuity wire and the foil with insulating tube . There must not be any conductive components in the junction box! Connect the shield connector = continuity wire on one side to the earth circuit connector . Do not use shielded and unshielded cables at the same time.
Content 1 lm
From 1.80EUR *

Stock status:

Add to wishlist
 Shielded cable (N)YM(St)-J | 3 x 2.5 mm² | 1 meter Shielded cable (N)YM(St)-J | 3 x 2.5 mm² | 1 meter
Low priced shielded installation cables for the protection against low-frequency electric fields (LF). For installations over, up, in and under finery, in dry, moistens and wet areas, as well as in the brick-work and concrete. Also suitable for use outside, if protected against sun exposure. Excluded for direct imbedding in vibration, shaking and ramming concrete. Technical data Shielded PVC-sheathed cable (adapted to DIN VDE 0250 part 204/209) PVC self-extinguishing and flame retardant according to VDE 0482-332-1-2, DIN EN 60332-1-2 / IEC 60332-1 (equivalent DIN VDE 0472 part 804 test method B) CE = This product is conform with the EC Low-Voltage Directive 2006/95/EG Direct current resistance to DIN VDE 0295 Operating temperature -40°C to +70°C, cabling temperature -5°C to +70°C Nominal voltage U0/U: 300/500 V, current load according to VDE 0100 Test procedures according to DIN VDE 0472, test ac voltage 50 Hz, 2000 V Bending radius accoording to DIN VDE 0298: 4 x D Radiation resistance: Up to 80x106 cJ/kg (up to 80 Mrad) Variants Wire count / cross section Outer diameter Weight 3 x 1.5 mm² 10.5 mm 154 g/m 3 x 2.5 mm² 12.0 mm 217 g/m 5 x 1.5 mm² 12.0 mm 208 g/m 5 x 2.5 mm² 13.5 mm 208 g/m Construction 1) Solid copper conductor; 2) Insulation: cross linked polyethylene; 3) Common PVC core covering; 4) (St)-Screen: Coated aluminium foil with 1.5 mm wire; 5) PVC outer sheath; Information on installing Connect the ground wiring of the junction box with the ground wiring of the cable during installation! Always connect green-yellow with green-yellow , in no case connect it with the continuity wire! Protect the bare continuity wire and the foil with insulating tube . There must not be any conductive components in the junction box! Connect the shield connector = continuity wire on one side to the earth circuit connector . Do not use shielded and unshielded cables at the same time.
Content 1 lm
From 2.20EUR *

Stock status:

Add to wishlist
 Shielded cable (N)YM(St)-J | 5 x 1.5 mm² | 1 meter Shielded cable (N)YM(St)-J | 5 x 1.5 mm² | 1 meter
Low priced shielded installation cables for the protection against low-frequency electric fields (LF). For installations over, up, in and under finery, in dry, moistens and wet areas, as well as in the brick-work and concrete. Also suitable for use outside, if protected against sun exposure. Excluded for direct imbedding in vibration, shaking and ramming concrete. Technical data Shielded PVC-sheathed cable (adapted to DIN VDE 0250 part 204/209) PVC self-extinguishing and flame retardant according to VDE 0482-332-1-2, DIN EN 60332-1-2 / IEC 60332-1 (equivalent DIN VDE 0472 part 804 test method B) CE = This product is conform with the EC Low-Voltage Directive 2006/95/EG Direct current resistance to DIN VDE 0295 Operating temperature -40°C to +70°C, cabling temperature -5°C to +70°C Nominal voltage U0/U: 300/500 V, current load according to VDE 0100 Test procedures according to DIN VDE 0472, test ac voltage 50 Hz, 2000 V Bending radius accoording to DIN VDE 0298: 4 x D Radiation resistance: Up to 80x106 cJ/kg (up to 80 Mrad) Variants Wire count / cross section Outer diameter Weight 3 x 1.5 mm² 10.5 mm 154 g/m 3 x 2.5 mm² 12.0 mm 217 g/m 5 x 1.5 mm² 12.0 mm 208 g/m 5 x 2.5 mm² 13.5 mm 208 g/m Construction 1) Solid copper conductor; 2) Insulation: cross linked polyethylene; 3) Common PVC core covering; 4) (St)-Screen: Coated aluminium foil with 1.5 mm wire; 5) PVC outer sheath; Information on installing Connect the ground wiring of the junction box with the ground wiring of the cable during installation! Always connect green-yellow with green-yellow , in no case connect it with the continuity wire! Protect the bare continuity wire and the foil with insulating tube . There must not be any conductive components in the junction box! Connect the shield connector = continuity wire on one side to the earth circuit connector . Do not use shielded and unshielded cables at the same time.
Content 1 lm
From 2.20EUR *

Stock status:

Add to wishlist
 Shielded cable (N)YM(St)-J | 5 x 2.5 mm² | 1 meter Shielded cable (N)YM(St)-J | 5 x 2.5 mm² | 1 meter
Low priced shielded installation cables for the protection against low-frequency electric fields (LF). For installations over, up, in and under finery, in dry, moistens and wet areas, as well as in the brick-work and concrete. Also suitable for use outside, if protected against sun exposure. Excluded for direct imbedding in vibration, shaking and ramming concrete. Technical data Shielded PVC-sheathed cable (adapted to DIN VDE 0250 part 204/209) PVC self-extinguishing and flame retardant according to VDE 0482-332-1-2, DIN EN 60332-1-2 / IEC 60332-1 (equivalent DIN VDE 0472 part 804 test method B) CE = This product is conform with the EC Low-Voltage Directive 2006/95/EG Direct current resistance to DIN VDE 0295 Operating temperature -40°C to +70°C, cabling temperature -5°C to +70°C Nominal voltage U0/U: 300/500 V, current load according to VDE 0100 Test procedures according to DIN VDE 0472, test ac voltage 50 Hz, 2000 V Bending radius accoording to DIN VDE 0298: 4 x D Radiation resistance: Up to 80x106 cJ/kg (up to 80 Mrad) Variants Wire count / cross section Outer diameter Weight 3 x 1.5 mm² 10.5 mm 154 g/m 3 x 2.5 mm² 12.0 mm 217 g/m 5 x 1.5 mm² 12.0 mm 208 g/m 5 x 2.5 mm² 13.5 mm 208 g/m Construction 1) Solid copper conductor; 2) Insulation: cross linked polyethylene; 3) Common PVC core covering; 4) (St)-Screen: Coated aluminium foil with 1.5 mm wire; 5) PVC outer sheath; Information on installing Connect the ground wiring of the junction box with the ground wiring of the cable during installation! Always connect green-yellow with green-yellow , in no case connect it with the continuity wire! Protect the bare continuity wire and the foil with insulating tube . There must not be any conductive components in the junction box! Connect the shield connector = continuity wire on one side to the earth circuit connector . Do not use shielded and unshielded cables at the same time.
Content 1 lm
From 3.00EUR *

Stock status:

Add to wishlist

* All prices are gross prices which include tax, in addition shipping costs. Copyright © 2016 YSHIELD GmbH & Co. KG